You are here: User Guide > Referenced Mode

Referenced Mode Testing Processes

In the Referenced mode, the devices under test use a specific audio file (called reference file or test file) provided by Frontline whose contents are already known to the Frontline software. The software compares the parameters of the received audio data against its parameters and presents analysis for the user. Commonly, in Bluetooth technology the music sent via A2DP and speech sent via HFP. There are a few ways users can conduct referenced mode testing depending upon what profile they are using. The figure 17 shows the source of the audio and the medium through which it can be accessed by Source device to send to sink device via Bluetooth.

Referenced Mode Testing Process Between Two DUTs
Audio Source Process to Send Using A2DP Process to Send Using HFP
A file stored on the device’s local memory Play the locally stored file on the audio source device Play using the third party App that transmits music data on HFP.
Streaming audio over a cellular network

Play the test in a browser on the audio source device

https://youtu.be/rmirDbikrtM

Make a call to 434-964-1407 or 434-964-1304 through a cellular network. The phone number receiving the call playbacks recorded test signal.
Streaming audio over a Wi-Fi network

Play the test in a browser on the audio source device

https://youtu.be/rmirDbikrtM

Make a call to 434-964-1407 or 434-964-1304 through a VoIP provider such as Skype. The phone number receiving the call playbacks recorded test signal.

Potential problem: The VoIP provider might use custom codecs and cause undesirable behavior.

A2DP

Playing the test file locally

The simplest way to perform music data testing is to directly play the reference file from DUT1 to DUT2. To do that, save the reference file provided with the Frontline software on the Source device. Then connect the Bluetooth enabled devices and play the music file from one device to the other. The software will automatically detect the mode and present analysis for the user.

Playing the test file via Internet

If the user is testing a scenario where they need to analyze audio played through the internet (either using Wi-Fi or cellular data plan), they may access the reference file on YouTube provided by Frontline - https://youtu.be/rmirDbikrtM. Note that the software is only analyzing the Bluetooth link between the two DUTs. Any abnormalities at the Wi-Fi and cellular network level will affect the audio quality that may not be Bluetooth protocol related and the software will not be able to detect that.

HFP

Playing the test file by calling a phone number

Frontline provides the following phone numbers - 434-964-1407 and 434-964-1304 that users can call, to conduct speech audio data analysis over Bluetooth. The calls can be made using the cellular network (most common method) or VoIP. Again, the VoIP provider might use custom codecs and cause undesirable behavior which cannot be detected by Audio Expert System™ software.

Playing the test file using Third party Apps

Bluetooth Audio Expert System™ Reference mode testing can be accomplished using third party apps on Android, iOS, and Windows phones. The following apps are available from their respective App stores:

Note: When selecting and using these apps, thoroughly review all the vendor documentation. While Teledyne LeCroy has conducted testing of these apps, Teledyne LeCroy has not completed full interoperability testing with our library of Bluetooth devices and does not warrant the use of these apps with every device when using the following procedures. Teledyne LeCroy does not provide support or maintenance for third party apps. Any issues or questions should be directed to the app developer.

  1. In the following steps Device Under Test 1 (DUT1) is the device sending the reference test file to DUT2.
  2. Download the third party app to DUT1 and follow the app vendor's instructions for installation and use.
  3. Load the Audio Expert System reference test file

    "Test_1.02_64.1kHz_16Bit.wav"

    on DUT1.The test file is stored on the users computer In the directory "\Frontline <version #>\Development Tools\Audio Expert Test Files\".

    Note: Reference test files are periodically updated. Shown here is an example. Files delivered with your latest Frontline software version may have changed. Contact Teledyne LeCroy Technical Support for information on the latest reference file versions.

  4. With the BPA 600 or Sodera connected to the computer, configure the datasource, and follow procedures to capture data.
  5. Launch Audio Expert System by clicking on the Control window Audio Expert System.
  6. Turn on Bluetooth on your DUTs, DUT1 and DUT2. Turn on the third party Bluetooth app for routing the reference file over A2DP or HFP by following the vendor's directions.
  7. Send the reference test file from DUT1 to DUT2 via the third party app.
  8. Observe the events in the Audio Expert System™Events Table. Look for an event Description:

    “TestIDFound : REF: Test ID 1.02, Channel Gain = -11.8 dB TermFreq=400.0”.

    Note: This is an example. The display may vary with the reference file version.

    The Frontline analyzer has successfully detected the reference test signal and the system is locked into reference mode.

Test Cases for Referenced Mode Testing


Also see these related topics...Related Topics Link Icon